Casio Edifice ECW-M300EDB-1AER инструкция

Casio Edifice ECW-M300EDB-1AER
8.1 · 5
PDF инструкция
 · 7 страниц(ы)
английский
инструкцияCasio Edifice ECW-M300EDB-1AER

Operation Guide 5117

2
Proper signal reception can be difficult or even impossible under the conditions listed
below.
Signal reception normally is better at night than during the day.
Time calibration signal reception takes from two to seven minutes, but in some
cases it can take as long as 14 minutes. Take care that you do not perform any
button operations or move the watch during this time.
Inside or
among
buildings
Inside a
vehicle
Near a
construction
site, airport, or
other sources
of electrical
noise
Near high-
tension power
lines
Among or
behind
mountains
Near household
appliances,
office
equipment,
or a mobile
phone
The time calibration signal the watch will attempt to pick up depends on its current
Home City code setting as shown below.
Home City Code
LON, PAR , BER, ATH,
LIS, MAD, ROM, STO, MOW*
HKG, BJS
TPE, TYO, SEL
HNL*, ANC*, LAX, DEN,
CHI, NYC, YVR, YEA, MEX,
MIA, YTO, YHZ, YYT
Frequency
60.0 kHz
77.5 kHz
68.5 kHz
40.0 kHz
60.0 kHz
60.0 kHz
Transmitter
Anthorn (England)
Mainflingen (Germany)
Shangqiu City (China)
Fukushima (Japan)
Fukuoka/Saga (Japan)
Fort Collins, Colorado
(the United States)
* The areas covered by the HNL, ANC, and MOW city codes are quite far from the
time calibration signal transmitters, and so certain conditions may cause problems
with signal reception.
Calibration signal reception is disabled while a countdown timer operation is in
progress.
Approximate Reception Ranges
2,000 miles
(3,000 kilometers)
U.K. and German Signals
Anthorn
Mainflingen
1,500 kilometers
500 kilometers
The Anthorn signal is
receivable within this
area.
U.S. Signal
Fort Collins
600 miles
(1,000 kilometers)
500 kilometers
Changchun
Beijing
1,500 kilometers
China Signal
Shanghai
Hong Kong
Shangqiu
Chengdu
Signals are receivable in the Taiwan area when reception conditions are good.
1,000 kilometers
1,000 kilometers
Fukuoka/Saga
500 kilometers
Fukushima
500 kilometers
Japan Signals
Signal reception may not be possible at the distances that are futurer than those
noted below during certain times of the year or day. Radio interference may also
cause problems with reception.
Mainflingen (Germany) or Anthorn (England) transmitters: 500 kilometers
(310 miles)
Fort Collins (United States) transmitter: 600 miles (1,000 kilometers)
Fukushima or Fukuoka/Saga (Japan) transmitters: 500 kilometers (310 miles)
Shangqiu (China) transmitter: 1500 kilometers (910 miles)
Even when the watch is within the reception range of the transmitter, signal
reception will be impossible if the signal is blocked by mountains or other geological
formations between the watch and signal source.
Signal reception is affected by weather, atmospheric conditions, and seasonal
changes.
Midnight
*
1:00 am*
1:00 am*
2:00 am*
2:00 am*
3:00 am*
3:00 am*
4:00 am*
About Auto Receive
The watch receives the time calibration signal automatically up to six times a day (five
times for the China signal). When any auto receive is successful, the remaining auto
receive operations are not performed. The reception schedule (calibration times)
depends on your currently selected Home City, and whether standard time or Daylight
Saving Time is selected for your Home City.
1:00 am
2:00 am
2:00 am
3:00 am
3:00 am
4:00 am
4:00 am
5:00 am
2:00 am
3:00 am
3:00 am
4:00 am
4:00 am
5:00 am
5:00 am
Midnight
*
3:00 am
4:00 am
4:00 am
5:00 am
5:00 am
Midnight
*
Midnight
*
1:00 am*
4:00 am
5:00 am
5:00 am
Midnight
*
Midnight
*
1:00 am*
1:00 am*
2:00 am*
5:00 am
Midnight
*
Midnight
*
1:00 am*
1:00 am*
2:00 am*
2:00 am*
3:00 am*
LON
LIS
PAR
BER
MAD
ROM
STO
ATH
MOW
Standard Time
Daylight Saving Time
Standard Time
Daylight Saving Time
Standard Time
Daylight Saving Time
Standard Time
Daylight Saving Time
Your Home City
1 2 3 4 5 6
Auto Receive Start Times
Your Home City
1 2 3 4 5 6
Auto Receive Start Times
HKG
BJS
TYO
TPE
SEL
HNL
ANC
LAX
DEN
CHI
NYC
YVR
YEA
MEX
MIA
YTO
YHZ
YYT
Standard Time
Standard Time
Standard Time and
Daylight Saving Time
1:00 am
Midnight
Midnight
2:00 am
1:00 am
1:00 am
3:00 am
2:00 am
2:00 am
4:00 am
3:00 am
3:00 am
5:00 am
4:00 am
4:00 am
5:00 am
5:00 am
*Next day
Note
When a calibration time is reached, the watch will receive the calibration signal only
if it is in either the Timekeeping Mode or World Time Mode. Reception is not
performed if a calibration time is reached while you are configuring settings.
Auto receive of the calibration signal is designed to be performed early in the
morning, while you sleep (provided that the Timekeeping Mode time is set correctly).
Before going to bed for the night, remove the watch from your wrist, and put it in a
location where it can receive the signal easily.
The watch receives the calibration signal for two to 14 minutes everyday when the
time in the Timekeeping Mode reaches a calibration time. Do not perform any button
operation within 14 minutes before or after the calibration times. Doing so can
interfere with correct calibration.
Remember that reception of the calibration signal depends on the current time in
your Home City, as kept in the Timekeeping Mode.
To perform manual receive
1. Place the watch on a stable surface so its 12 o’clock
side is facing towards a window.
2. In the Timekeeping Mode, hold down A for about two
seconds until the watch beeps.
3. The digital display will go blank, and the left dial hand
will move to R (READY). This indicates that the watch is
getting ready for time calibration signal reception.
See the information under “Signal Reception
Troubleshooting” if you experience problems.
The left dial hand will move to W (WORK) and stay there
while actual reception is in progress.
If signal reception is unstable during reception, the left
dial hand may move between W (WORK) and
R (READY).
The hour and minute hands continue to keep time
normally.
Receiving
R (READY) W (WORK)
Time calibration signal reception takes from two to
7 minutes, but in some cases it can take as long as
14 minutes. Take care that you do not perform any
button operations or move the watch during this time.
When signal receive operation is successful, GET
appears on the upper display and the lower display
shows the time and date of the successful operation.
The watch will adjust its time setting in accordance to
with the information provided by the signal.
The watch will return to the Timekeeping Mode if you
press A or if you do not perform any operation for
about one or two minutes.
ERR will appear on the upper display if the receive
operation is not successful. The watch will not adjust its
time setting in this case. Press A to return to the
Timekeeping Mode.
Receive failed
Receive successful
Note
To interrupt a receive operation and return to the Timekeeping Mode, press any
button.
To check the latest signal reception results
In the Timekeeping Mode, press A to view the last successful receive time and date.
Press A again to return to the previous screen.
Date
Hour : Minutes
Signal Reception Troubleshooting
Check the following points whenever you experience problems with signal reception.
You performed some button operation
during the auto receive operation.
The watch is not in the Timekeeping
Mode or World Time Mode.
The watch is in a location where the
signal cannot be received for some
reason.
A countdown timer operation is in
progress.
Radio interference is often present
during the day time, which can
interfere with calibration signal
reception.
I can’t
receive a
time
calibration
signal.
Perform manual signal
receive at night or wait until
the next auto signal receive
operation is performed.
Enter the Timekeeping
Mode or World Time Mode
and try again.
Enter the Countdown Timer
Mode and stop the
countdown.
Check to make sure the
watch is in a location where
it can receive the signal.
Probable CauseProblem What you should do
Time setting
is incorrect
following
signal
reception.
If the time is one hour off, the DST
setting may be incorrect.
The Home City code setting is not
correct for the area where you are
using the watch.
The home position of the hands is off.
Change the DST setting to
Auto DST.
Select the correct Home
City code.
Enter the home position
adjustment mode and adjust
the home position.
For further information, see “Important!” under “Time Calibration Signal Reception”
and “Radio-controlled Atomic Timekeeping Precautions”.

Инструкция

Посмотреть инструкция для Casio Edifice ECW-M300EDB-1AER бесплатно. Руководство относится к категории Часы, 5 человек(а) дали ему среднюю оценку 8.1. Руководство доступно на следующих языках: английский. У вас есть вопрос о Casio Edifice ECW-M300EDB-1AER или вам нужна помощь? Задайте свой вопрос здесь

Нужна помощь?

У вас есть вопрос о Casio Edifice ECW-M300EDB-1AER а ответа нет в руководстве? Задайте свой вопрос здесь Дай исчерпывающее описание проблемы и четко задайте свой вопрос. Чем детальнее описание проблемы или вопроса, тем легче будет другим пользователям Casio Edifice ECW-M300EDB-1AER предоставить вам исчерпывающий ответ.

Количество вопросов: 0

Технические характеристики Casio Edifice ECW-M300EDB-1AER

Ниже вы найдете технические характеристики изделия и руководства по эксплуатации Casio Edifice ECW-M300EDB-1AER.

Главная
Бренд Casio
Модель Edifice ECW-M300EDB-1AER
Изделие Часы
Язык английский
Тип файла Руководство пользователя (PDF)

Часто задаваемые вопросы

Не можете найти ответ на свой вопрос в руководстве? Вы можете найти ответ на свой вопрос ниже, в разделе часто задаваемых вопросов о Casio Edifice ECW-M300EDB-1AER.

Не нашли свой вопрос? Задайте свой вопрос здесь

Нет результатов