Casio Radio Controlled WVA-470DE-1AVEF инструкция

Casio Radio Controlled WVA-470DE-1AVEF
7.7 · 5
PDF инструкция
 · 6 страниц(ы)
английский
инструкцияCasio Radio Controlled WVA-470DE-1AVEF

Operation Guide 3353 3354 5053

2
Important!
When getting ready to receive the time calibration signal, position the watch as
shown in the nearby illustration, with its 12 oclock side facing towards a window.
This watch is designed to receive a time calibration signal late at night. Because of
this, you should place the watch near a window as shown in the illustration when you
take it off at night. Make sure there are no metal objects nearby.
12 o’clock
or
Make sure the watch is facing the right way.
Proper signal reception can be difficult or even impossible under the conditions listed
below.
Signal reception is normally better at night than during the day.
Time calibration signal reception takes from two to seven minutes, but in some
cases it can take as long as 14 minutes. Take care that you do not perform any
button operations or move the watch during this time.
Inside or
among
buildings
Inside a
vehicle
Near
household
appliances,
office
equipment,
or a mobile
phone
Near a
construction
site, airport, or
other sources
of electrical
noise
Near high-
tension
power lines
Among or
behind
mountains
In April 2007, the U.K. signal transmitter was moved from Rugby to Anthorn, which
resulted in a slight shift in the approximate reception range of the signal. The shift is
so slight that there is virtually no change in the ability to receive the signal.
Approximate Reception Ranges
Anthorn
Mainflingen
500 kilometers
1,500 kilometers
U.K. signal transmitter
approximate reception
range as of April 2007
Even when the watch is within the reception range of a transmitter, signal reception
may be impossible at times due to the effects of geographic contours, structures,
weather, the season of the year, the time of day, radio interference, etc. Note that the
signal becomes weaker at distances of approximately 500 kilometers from the
transmitter, which means that the influence of the conditions listed above becomes
even greater.
See the information under Signal Reception Troubleshooting if you experience
problems with time calibration signal reception.
About Auto Receive
When auto receive is turned on, the watch automatically starts to receive the time
calibration signal when the time in the Timekeeping Mode reaches 0:00 a.m., 1:00
a.m., 2:00 a.m., 3:00 a.m., and 4:00 a.m. each day (calibration times). The watch will
also perform an additional auto receive at 5:00 a.m. if none of the regularly scheduled
auto receive are successful.
Note
Auto receive is performed only if the watch is in the Timekeeping Mode or World
Time Mode when one of the calibration times is reached. It is not performed if a
calibration time is reached while an alarm is sounding, or while you are configuring
settings (while settings are flashing on the display).
When a reception starts, the second hand will move at high speed to the 12 oclock
position where it will stop until the reception is complete.
Auto receipt of the calibration signal is designed to be performed early in the
morning, while you sleep (provided that the Timekeeping Mode time is set correctly).
Before going to bed for the night, remove the watch from your wrist, and put it in a
location where it can easily receive the signal.
When auto receive is turned on, the watch receives the calibration signal for two to
seven minutes everyday when the time in the Timekeeping Mode reaches each of
the five calibration times. Do not perform any button operation within seven minutes
before or after any of the five calibration times. Doing so can interfere with correct
calibration.
Remember that reception of the calibration signal depends on the time kept in the
digital display. The reception will be performed whenever the display shows one of
the five calibration times, regardless of whether or not the displayed time is actually
the correct time.
When two, three, four, or five receptions are successful, the watch uses the data of
the last reception for calibration. When only one reception is successful, the watch
uses the data of the successful reception.
About the Receiving Indicator
The receiving indicator shows the strength of the calibration signal being received. For
best reception, be sure to keep the watch in a location where signal strength is
strongest.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|

Receiving indicator

Weak

(Level 1)

Strong

(Level 4)

Even in an area where signal strength is strong, it takes about 10 seconds for signal
reception to stabilize enough for the receiving indicator to indicate signal strength.
Use the receiving indicator as a guide for checking signal strength and for finding the
best location for the watch during signal reception.
The Level 4 receiving indicator appears on the Timekeeping Modes Receiving
Indicator and Seconds Count screen only. The Level 4 receiving indicator is not
displayed if signal reception was unsuccessful or after manual adjustment of the
current time setting.
The Level 4 receiving indicator indicates that at least one of the five calibration
signal reception was successful. Note, however, that the Level 4 receiving indicator
is cleared from the display at 3:00 a.m. each day.

To perform manual receive

1. Place the watch on a stable surface so its top (12
oclock side) is facing towards a window.
2. In the Timekeeping Mode, hold down D for about two
seconds until the watch beeps.
3. Release D and RC flashes to indicate that signal
reception has started.
When a reception starts, the second hand will move at
high speed to the 12 oclock position where it will stop
until the reception is complete.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|

Receiving indicator

Time calibration signal reception normally takes from two to seven minutes, but in
some cases it can take as long as 14 minutes. Take care that you do not perform any
button operations or move the watch during this time.
After signal reception is complete, the display of the watch changes to the last signal
screen.
Note
To interrupt a reception and return to the Timekeeping Mode, press D.
If the reception is unsuccessful, the message

ERR appears on the display for about

one or two minutes. After that, the watch returns to the Timekeeping Mode.
You can also change from the last signal or

ERR screen to the normal timekeeping

screen by pressing D.

To turn auto receive on and off

1. In the Timekeeping Mode, hold down A until the
transmitter indicator starts to flash, which indicates the
setting screen.
The second hand will move at high speed to the 12
oclock position, where it will stop.
2. Press C three times to move the flashing to the auto
receive on/off setting.
3. Press D to toggle auto receive on (
ON
) and off (
OF
).
If the current Home City setting is a city code that
does not support auto receive,
--
appears in place
of the on/off indicator. This means you cannot turn
auto receive on or off.
4. Press A twice to exit the setting screen.
The second hand will advance at high speed to the correct position in accordance
with the digital time seconds count, and resume normal movement from there.
For information about city codes that support signal reception, see To set your
Home City.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|

On/off status

Signal Reception Troubleshooting
Check the following points whenever you experience problems with signal reception.
Problem
Cannot perform
manual receive.
Auto receive is
turned on, but
the Level 4
receiving
indicator does
not appear on
the Timekeeping
Mode display.
Time setting is
incorrect
following signal
reception.
Probable Cause
The watch is not in the Timekeeping Mode.
Your current Home City is not one of
the following city codes: BER, PA R,
ATH, or LON.
You changed the time setting manually.
The watch was not in the Timekeeping
or World Time Mode, or you were
performing some button operation
during auto receive.
Even if reception is successful, the
Level 4 receiving indicator disappears
every day at 3 a.m.
Time data (hour, minutes, seconds)
only was received during the last
reception. The Level 4 receiving
indicator appears only when time data
and date data (year, month, day) are
both received.
If the time is one hour off, the DST
setting may be incorrect.
The Home City code setting is not
correct for the area where you are
using the watch.
What you should do
Enter the Timekeeping Mode
and try again.
Select BER, PAR, ATH, or
LON as your Home City.
Select the appropriate
transmitter setting for your
current location.
Select the appropriate
transmitter setting for your
current location.
Perform manual receive or
wait until the next auto
receive is performed.
Check to make sure the
watch is in a location where it
can receive the signal.
Change the DST setting to
Auto DST.
Select the correct Home City
code.
For further information, see Important! under Time Calibration Signal Reception
and Radio-controlled Atomic Timekeeping Precautions.

World Time

The World Time Mode digitally displays the current time in
30 cities (29 time zones) around the world.
Pressing A in the World Time Mode causes the
applicable city code to appear on the digital display for
about two seconds.
If the current time shown for a city is wrong, check your
Home City time settings and make the necessary
changes.
The watch will perform a signal reception even if it is in
the World Time Mode when a calibration time is
reached. If this happens, the World Time Mode time
settings will be adjusted in accordance with the
Timekeeping Modes Home City time.
All of the operations in this section are performed in the
World Time Mode, which you enter by pressing C.

City Code

Current time in the

selected city code

To view the time in another city

While in the World Time Mode, press D to scroll through the city codes (time zones).
For full information on city codes, see the City Code Table.

Инструкция

Посмотреть инструкция для Casio Radio Controlled WVA-470DE-1AVEF бесплатно. Руководство относится к категории Часы, 5 человек(а) дали ему среднюю оценку 7.7. Руководство доступно на следующих языках: английский. У вас есть вопрос о Casio Radio Controlled WVA-470DE-1AVEF или вам нужна помощь? Задайте свой вопрос здесь

Нужна помощь?

У вас есть вопрос о Casio Radio Controlled WVA-470DE-1AVEF а ответа нет в руководстве? Задайте свой вопрос здесь Дай исчерпывающее описание проблемы и четко задайте свой вопрос. Чем детальнее описание проблемы или вопроса, тем легче будет другим пользователям Casio Radio Controlled WVA-470DE-1AVEF предоставить вам исчерпывающий ответ.

Количество вопросов: 0

Технические характеристики Casio Radio Controlled WVA-470DE-1AVEF

Ниже вы найдете технические характеристики изделия и руководства по эксплуатации Casio Radio Controlled WVA-470DE-1AVEF.

Главная
Бренд Casio
Модель Radio Controlled WVA-470DE-1AVEF
Изделие Часы
Язык английский
Тип файла Руководство пользователя (PDF)

Часто задаваемые вопросы

Не можете найти ответ на свой вопрос в руководстве? Вы можете найти ответ на свой вопрос ниже, в разделе часто задаваемых вопросов о Casio Radio Controlled WVA-470DE-1AVEF.

Не нашли свой вопрос? Задайте свой вопрос здесь

Нет результатов