Sevenoak SK-GH01

Sevenoak SK-GH01 инструкция

(1)
  • There is a small hole on the side of the
    base of the Head that can be used to
    apply greater leverage for installing or
    removing the Head from your tripod.
    The hole is designed to accommodate
    a 5/32 hex key (commonly used by our
    customers to attach quick-release plates
    to lenses & cameras). Note: The hex key
    is only used as a leverage arm, it does not engage a fastener
    inside the leverage hole (the hole is not threaded). If you do
    not have an appropriate sized hex key, any strong metal rod
    that will fit into the hole can be used (e.g. a small screwdriver).
    Prerequisite: In order to attach your lens to the Sevenoak
    Gimbal Head, it must be fitted with an Arca-Swiss style quick
    -release plate or foot (see details below).
    In order to attach your lens to the Sevenoak Gimbal Head, it must
    be fitted with an Arca-Swiss style quick-releaseplate or foot (sold
    separately). We oer a line of such plates. For more information
    see our catalog or website: www.sevenoak.biz(click on “Lens
    Plates”).
    We strongly recommend using Sevenoak plates because we
    carefully match your lens with the appropriate size plate that
    Position the Head’s platform at its
    lowest position and level to the
    ground. Tighten the Head’s tilt knob.
    Mount your lens (with camera body
    attached). Stand behind the
    lens/camera setup and grab the
    camera body as if you are going
    to take a picture.
    Step 1: Tighten the tilt knob of the
    swing arm-make sure that the Head’s
    platform is level so that the Head is
    stable while you are loading your lens.
    Step 2: Open the jaws of the quick-
    release clamp wide enough so that the
    jaws clear the entire width of the QR
    plate attached to the foot of your lens.
    Step 3: While supporting your lens,insert
    the quick-release plate on your lens into
    the jaws of the clamp and tighten the
    clamp securely.Make sure the quick-release
    plate is seated properly and captive in the
    clamp jaws before letting go of the lens.
    Using the Leverage Hole:
    Attching Your Lens To The Sevenoak Gimbal Head:
    Prerequisite: Arca-Swiss Style Lens Plate :
    Balancing Your Lens On The Sevenoak Gimbal Head:
    STEP 1: Preparing to Balance:
    Loosen the tilt knob of the Sevenoak Gimbal Head SLOWLY-stand
    ready to catch the lens or camera body should one end or the
    other rapidly tilt down! Adjust the horizontal position of the lens
    forward or backwards depending on how the lens tips (see fig-
    ures below). SAFETY NOTE: Retighten the clamp after each
    adjustment, no matter how small! Use the two safety stop screws
    provided with your Wimberley lens plate or replacement foot to
    prevent the lens/camera combo from sliding out of the clamp
    when loosened.
    If the front of the lens tilts downward
    you will need to sild the lens backward
    in the clamp toward you.
    If the front of the lens tilts upward,
    you willneed to slide lens forward
    away from you.
    STEP 2: Balance the Horizontal Position of the Lens:
    Use caution when adjusting
    the center screw (see page 7).
    Dimensions: (h,w,d): 23.5*8.9*24.7cm
    Weight: 1.4 kg
    It is important to read these instructions.
    Setting up this Head is not dicult, but reading these instructions
    will allow you to get the most out of the product.
    Instructions: Sevenoak Gimbal Head SK-GH01
    Mounting SK-GH01to a tripod:
    Setting up the Sevenoak Gimbal Head
    Assembling the Sevenoak Gimbal Head is a simple matter
    of attaching the Head’s platform (detached to make it
    more compact for shipping) to the swinging arm of the
    Head. Do not tighten the platform knob unless it is mounted
    on the Head.
    Step 1: Align the platform jaws
    properly with the dovetail grooves
    in the swing arm. Slide the platform
    onto the swing arm of the Head.
    Slide the platform all the way
    down until it hits the “stop” at the
    bottom.
    Step 2: Tighten the platform knob
    firmly. (The platform should lock
    securely to the arm without the
    need to apply extreme torque).
    The platform height will be adjusted
    later if needed.
    Step 1: Firmly tighten the lower (pan) knob.
    Step 2: Position the Head with
    the spool mounting hole (located
    under the spool) directly over the
    threaded tripod mounting stud.
    It is important to keep the Head
    completely straight (vertical) over
    the stud to keep the spool threads
    from cross - threading.
    Step 3: Screw the Head clockwise
    onto the stud of your tripod until
    it seats the bottom spool of the
    Head and the tripod mounting
    plate. Use the leverage hole to
    achieve a tighter attachment if
    desired (see below).Loosen the
    pan knob slightly and rotate the
    Head to check the security of
    the mount. The spool should not
    loosen when you turn the Head
    counterclockwise, and the Head
    should not wobble at all.
    Assembling The Sevenoak Gimbal Head:
    IMPORTANT WARNINGS!
    Tit Knob
    Upright
    Arm
    Platform Knob
    Platform
    Pan Knob
    Quick-Release Knob
    Never loosen or remove the 3 small
    screws on the top of the pan base.
    If your tripod has a smaller ¼” mounting stud , check to see
    if it is a reversible stud with a 3/8”-16 threaded section on the
    other end. If so, reverse the stud and use the 3/8” end of the
    stud. If the ¼” stud is not reversible, you will need to use a
    reducer bushing to mount the Head to the tripod. Robust
    brass bushings can be ordered through our website.
    1
    1
    1
    3
    2
    2
    3
    SK-GH01
    Gimbal Head
    2
    will allow you to properly balance your lens on our gimbal head.
    Our plates are also all equipped with safety stops which protect
    your gear from accidentally slipping out of a compatible quick-
    release clamp.If you use plates from other manufacturers you
    will need to make sure that they are the proper length and pro-
    portion that we recommend for your lens.Compare the plate
    length and profile to the recommended plate for your lens in our
    product catalog or on our web site.
    Page 1 Page 2 Page 3 Page 4
    2017 Sevenoak Inc.Visit us on the web at www.sevenoak.biz
Sevenoak SK-GH01

Нужна помощь?

Количество вопросов: 0

У вас есть вопрос о Sevenoak SK-GH01 или вам нужна помощь? Задайте его здесь. Полно и четко опишите проблему и сформулируйте свой вопрос. Чем больше вы сообщите о проблеме или вопросе, тем легче будет производителю Sevenoak SK-GH01 вам ответить.

Посмотреть руководство для Sevenoak SK-GH01 бесплатно. Руководство относится к категории Штативы, 1 человек(а) дали ему среднюю оценку 7.5. Руководство доступно на следующих языках: английский. У вас есть вопрос о Sevenoak SK-GH01 или вам нужна помощь? Задайте свой вопрос здесь

Технические характеристики Sevenoak SK-GH01

Главная
Бренд Sevenoak
Модель SK-GH01
Изделие Штатив
EAN 4897040881517
Язык английский
Тип файла PDF
Технические характеристики
Соединение 3/8 2011-05-04 11:27:54 2012-06-08 13:40:02 7947 23 8 Мбит/с 0000-00-00 00:00:00 2012-06-08 13:40:02 7953 32 8 ° 0000-00-00 00:00:00 2012-06-08 13:40:02 7954 33 8 x 0000-00-00 00:00:00 2012-06-08 13:40:02 7960 39 8 пикселей 0000-00-00 00:00:00 2012-06-08 13:
Тип головки штатива Карданный подвес
Максимальная емкость (вес) -
Встроенный уровень
Цвет товара Черный
Вес и размеры
Высота 235
Вес 1400

ManualsPDF.ru

Ищете руководство? ManualsPDF.ru гарантирует, что вы найдете необходимое за считанные секунды. В нашей базе данных содержится более 1 миллиона PDF-руководств от более 10 000 торговых марок. Ежедневно мы добавляем новейшие версии руководств, чтобы вы всегда могли найти необходимое именно вам. Все предельно просто: просто укажите название торговой марки и тип продукции в строке поиска, и вы сможете бесплатно и мгновенно просмотреть необходимое руководство.

ManualsPDF.ru

© Copyright 2020 ManualsPDF.ru. Все права сохранены.