Sevenoak SK-GH02

Sevenoak SK-GH02 инструкция

(1)
  • It is important to read these instructions.
    Instructions: SEVENOAK Gimbal Head SK-GH02
    Setting up the SEVENOAK Gimbal Head
    Assembling The SEVENOAK Gimbal Head
    IMPORTANT WARNINGS!
    Tit Knob
    Upright
    Arm
    Platform Knob
    Platform
    Pan Knob
    Quick-Release Knob
    Never loosen or remove the 3 small
    screws on the top of the pan base.
    Mounting SK-GH02 to a tripod
    Step 1:
    Step 2:
    Step 1:
    Step 2:
    Step 3:
    Setting up this Head is not dicult. but reading these instructions
    will allow you to get the most out of the product.
    Assembling the SEVENOAK Gimbal Head is a simple matter of
    attaching the Head's platform (detached to make it more compact
    for shipping) to the swinging arm of the Head. Do not tighten the
    platform knob unless it is mounted on the Head.
    Align the platform jaws
    properly with the dovetail grooves
    in the swing arm. Slide the platform
    onto the swing arm of the Head.
    Slide the platform all the way
    down until it hits the “stop” at the
    bottom.
        Tighten the platform knob
    firmly. (The platform should lock
    securely to the arm without the
    need to apply extreme torque).
    The platform height will be adjusted
    later if needed.
        Firmly tighten the lower (pan) knob.
        Position the Head with
    the spool mounting hole (located
    under the spool) directly over the
    threaded tripod mounting stud.
    It is important to keep the Head
    completely straight (vertical) over
    the stud to keep the spool threads
    from cross - threading.
        Screw the Head clockwise
    onto the stud of your tripod until
    it seats the bottom spool of the
    Head and the tripod mounting
    plate. Use the leverage hole to
    achieve a tighter attachment if
    desired (see picture on right).Loosen
    the pan knob slightly and rotate
    the Head to check the security of
    the mount. The spool should not
    loosen when you turn the Head
    counterclockwise, and the Head
    should not wobble at all.
    If your tripod has a smaller ¼” mounting stud , check to see
    if it is a reversible stud with a 3/8”-16 threaded section on the
    other end. If so, reverse the stud and use the 3/8” end of the
    stud. If the ¼” stud is not reversible, you will need to use a
    reducer bushing to mount the Head to the tripod.
    1
    1
    2
    3
    2
    Prerequisite: In order to attach your lens to the SEVENOAK
    Gimbal Head, it must be fitted with an Sevenoak style quick
    -release plate or foot (see details below).
    To attach your lens to the SEVENOAK Gimbal Head, it must be fitted
    with an Sevenoak quick-release plate or foot (included).
    Attaching Your Lens to The SEVENOAK
    Gimbal Head
    Prerequisite: Sevenoak
    Quick Release Plate
    Step 1:
        Tighten the tilt knob of the
    swing arm-make sure that the Head’s
    platform is level so that the Head is
    stable while you are loading your lens.
    Step 2:
        Open the jaws of the quick-release
    clamp wide enough so that the jaws
    clear the entire width of the QR plate
    attached to the foot of your lens.
    Step 3:
    While supporting your lens,insert
    the quick-release plate on your lens into
    the jaws of the clamp and tighten the
    clamp securely.Make sure the
    quick-release plate is seated properly
    and captive in the clamp jaws before
    letting go of the lens.
    1
    3
    2
    Position the Head's platform at its lowest position and parallel to the
    ground. Tighten the Head's tilt knob. Mount your lens (with camera
    body attached). Stand behind the lens/camera setup and hold the
    camera body as if you are going to take a picture.
    STEP 1: Preparing to Balance:
    Loosen the tilt knob of the SEVENOAK Gimbal Head SLOWLY
    -stand ready to catch the lens or camera body should one
    end or the other rapidly tilt down! Adjust the horizontal
    position of the lens forward or backwards depending on
    how the lens tips (see figures below). SAFETY NOTE: Re
    -tighten the clamp after each adjustment, no matter how
    small! Use the two safety stop screws provided with your
    lens plate or replacement foot to prevent the lens/camera
    combo from sliding out of the clamp when loosened.
    If the front of the lens tilts downward
    you will need to slide the lens back in
    the clamp, towards you.
    If the front of the lens, tilts upward
    you will need to slide lens forward,
    away from you.
    STEP 2: Balance the Horizontal Position of the Lens:
    Carbon Fiber Gimbal Tripod Head
    SK-GH02
    Weight: 1. 252kg
    Max load capacity: 15kg
    Page 2 Page 3 Page 4 Page 5
Sevenoak SK-GH02

Нужна помощь?

Количество вопросов: 0

У вас есть вопрос о Sevenoak SK-GH02 или вам нужна помощь? Задайте его здесь. Полно и четко опишите проблему и сформулируйте свой вопрос. Чем больше вы сообщите о проблеме или вопросе, тем легче будет производителю Sevenoak SK-GH02 вам ответить.

Посмотреть руководство для Sevenoak SK-GH02 бесплатно. Руководство относится к категории Штативы, 1 человек(а) дали ему среднюю оценку 7.5. Руководство доступно на следующих языках: английский. У вас есть вопрос о Sevenoak SK-GH02 или вам нужна помощь? Задайте свой вопрос здесь

Технические характеристики Sevenoak SK-GH02

Главная
Бренд Sevenoak
Модель SK-GH02
Изделие Штатив
EAN 4897040884419
Язык английский
Тип файла PDF
Технические характеристики
Материал Углеродный фильтр
Цвет товара Черный
Материал Aluminium, Carbon fiber
Цвет товара Черный
Соединение 3/8 2011-05-04 11:27:54 2012-06-08 13:40:02 7947 23 8 Мбит/с 0000-00-00 00:00:00 2012-06-08 13:40:02 7953 32 8 ° 0000-00-00 00:00:00 2012-06-08 13:40:02 7954 33 8 x 0000-00-00 00:00:00 2012-06-08 13:40:02 7960 39 8 пикселей 0000-00-00 00:00:00 2012-06-08 13:
Тип головки штатива Шар
Максимальная емкость (вес) 15
Встроенный уровень -
Вес и размеры
Вес 1120
Высота 236
Ширина 89
Глубина 251
Вес 1120
Высота 236
Ширина 89
Глубина 251

ManualsPDF.ru

Ищете руководство? ManualsPDF.ru гарантирует, что вы найдете необходимое за считанные секунды. В нашей базе данных содержится более 1 миллиона PDF-руководств от более 10 000 торговых марок. Ежедневно мы добавляем новейшие версии руководств, чтобы вы всегда могли найти необходимое именно вам. Все предельно просто: просто укажите название торговой марки и тип продукции в строке поиска, и вы сможете бесплатно и мгновенно просмотреть необходимое руководство.

ManualsPDF.ru

© Copyright 2020 ManualsPDF.ru. Все права сохранены.