Velbon VS-443D

Velbon VS-443D инструкция

  • -1
    Crank handle
    Individual part name
    Thank you very much for choosing Velbon tripod. Please read this manual carefully
    before you start using this tripod.
    Shoe lever
    Quick release plate QB-62
    Leg tip
    Low angle position
    Knob for leg angle
    Maximum height with Elevator
    Elevator movement
    Minimum Height
    Folded length
    Leg diameters
    Section of legs
    New weight
    Suggested loading weight
    Each specification is based on the estimated drawings. It may change depending on the actual parts assembled.
    How to attach your camera How to attach your camera
    How to install
    Caution: Please hold your camera surely when attach/detach quick release plate to the camera body.
    Also when install to the tripod/head, please make sure it locks firmly before you release your hand.
    Locking knob
    Elevator stopper
    Grip knob for
    Leg locking lever
    Shoe Lever
    Then plate
    rises up
    Shoe Lever
    Bubble Leveler
    Rotate shoe lever to release quick
    release plate (QB-62)
    Then QB-62 rises up to be slide out.
    Support your camera or other
    equipment with one hand,then with
    the other hand gradually release the
    Locking knob by turning
    anti-clockwise. You are now able to
    freely adjust the position of your
    camera in all 3 axes (vertically,
    horizontally and left –to-right) to the
    desired position.
    Rotate locking lever until quick-shoe
    (QB-62) can be removed from the
    socket. Turn camera screw clockwise
    to attach QB-62 to the base of your
    Place quick-shoe(QB-62) into socket
    and lock in place by rotating lever.
    Camera Screw
    Quick-Release Plate
    Shoe Lever
    How to use the head
    Head goes down in the case.
    When carrying tripod in the case, put
    head down so that you may carry
    easier on the shoulder.
    Watch your fingers not to be bound by
    the locking lever.
    Leg locking lever
    How to extend legs
    Rotating Grip knob for adjusting to
    unlock direction as seen in above
    drawing. Determining to the direction
    of the extension, lock by rotating the
    Grip for locking direction firmly.
    How to use the elevator
    Grip knob
    Grip knob
    Raise up
    How to use the elevator
    Unlocking the Elevator stopper, rotate
    the Crank handle to extend the
    Elevator. When the elevator extends
    to the desired position, lock the
    Elevator stopper firmly.
    Caution: Hold your camera body while
    operating elevator up/down carefully.
    Tighten surely !
    Caution to operate
    In the positioning to horizontal way,
    the center part of the Elevator may
    come to Loosen. So make sure
    locking the Grip Knob firmly. Tighten
    all the stoppers on the head and
    tripod surely.
    When extending horizontal,
    the head is apt to loosen
    depending on the angle of
    the arm.
    Caution: The longer Elevator extending,
    the easier to be loosen the tension of the
    Stopper or Grip Knob. Please grasp the
    Grip knob to hold tightly.
    Locking knob
    Locking knob
    Lock all the stoppers on the head and
    tripod, rotate head to anti-clockwise
    direction to unscrew the head from
    the tripod.
    Screw size UNC 1/4 inch.
    How to remove the head
    Knob for leg angle
    While legs are closed, slide the
    Knob for leg angle to right till it
    sounds Click to stay. Then legs are
    allowed to open to the full low angle
    By pushing the Reset button, the leg angle
    can be back to the normal position.
    Reset button
    Leg- angle adjusting
    Click !
    Automatically leg angle is
    back to left for Semi low angle
    position with a click.
    While closing the legs from Full low
    angle position, back to the Semi low
    angle position automatically, sliding to
    left with a click.
    Leg- angle adjusting
    Click !
    Slide to left further
    Closing further, the leg angle
    position changing to the Standard
    automatically. Each leg can be
    adjusted the angle independently for
    standing the tripod in the uneven
    Leg- angle adjusting
    Watch your camera,
    not to be laid down
    Caution to operate
    In case of setting whole unit including
    the camera, lens and tripod with even
    deeper angle of the Elevator
    extending, be careful to be laid down
    by losing the balance. Hold the Grip
    Knob tightly or hold the tripod leg until
    the balance become steady.
    Caution: Be aware that it becomes
    easier to be laid down when the Elevator
    extends to the horizontal way. Please keep
    holding tripod or camera in well supported
    Raise the Leg locking lever to extend
    the legs till desired position. Then
    lock the Legs firmly. When using the
    tripod legs less than fully extension,
    use the upper legs than lower ones
    because diameters are bigger and
Velbon VS-443D

Нужна помощь?

Количество вопросов: 0

У вас есть вопрос о Velbon VS-443D или вам нужна помощь? Задайте его здесь. Полно и четко опишите проблему и сформулируйте свой вопрос. Чем больше вы сообщите о проблеме или вопросе, тем легче будет производителю Velbon VS-443D вам ответить.

Посмотреть руководство для Velbon VS-443D бесплатно. Руководство относится к категории Штативы, 1 человек(а) дали ему среднюю оценку 7.5. Руководство доступно на следующих языках: английский. У вас есть вопрос о Velbon VS-443D или вам нужна помощь? Задайте свой вопрос здесь

Технические характеристики Velbon VS-443D

Бренд Velbon
Модель VS-443D
Изделие Штатив
EAN 4907990369840
Язык английский
Тип файла PDF
Предназначение Универсальная
Максимальная емкость (вес) 5 kg
Количество ножек 3 ножка(и)
Количекство секций ноги 4
Головка штатива QHD-53D
Материал Алюминий
Цвет товара Черный
Крепление 1/4", 3/8"
Вес и размеры
Высота (мин) 240 mm
Высота (макс) 1610 mm
Вес 1850 g