Vetta RT233

Vetta RT233 инструкция

(1)
  • Vetta’s RT233 is an upgraded version of RT33 cycle computer. It is recommended that this product to be installed by a
    qualified bicycle retailer. Failure to read the instructions and/ or improper installation of this device may void the
    warranty. If you have any doubts about the installation or the operations, contact your local bicycle retailer for
    clarification.
    Important: Do not use Zip-Ties, use the tapes provided with the package to hold wires to the frame, fork, bars or stem
    to avoid damaging or cutting the wires accidentally. Make sure excess wire is taped down or wrapped around brake cable
    housing to secure it.
    The Head Unit uses a CR2032 3-Volt Lithium button cell
    battery.
    Battery Run Time (1 hour training / day): Approx. 12 months
    Important: Most cycle computer problems are caused
    by weak or dead batteries. See the Trouble Shooting
    section near the end of the manual for details.
    1. Remove the battery cap from the bottom of the Head Unit using a coin.
    2. Install a new battery as shown with the positive (+) side facing out. Do not touch or bend
    any of the battery contacts during installation.
    3. Screw the battery cap firmly into place making sure the O-ring seal does not get pinched or distorted.
    Caution: To avoid damage to the battery cap, do not over tighten.
    WARNINGS & CAUTIONS
    ILLUSTRATIONS
    BATTERY INSTALLATION
    INSTALLATION
    HEAD UNIT
    COMPONENTS
    RT233
    1. Button
    2. Button
    3. Main Display
    4. Contact Pins
    5. Battery Compartment
    6. Battery Cap
    3
    1
    2
    4
    5
    6
    Standard Harness
    Replaceable Front Cover
    2 Screen Display Windows
    EZ Tire Set
    Service Timer
    Auto Awake & Start-up
    Current Speed
    Cumulative Odometer
    Trip Distance
    12/24 Hour Clock
    FUNCTIONS / FEATURES
    1
    4
    5
    6
    7
    9
    8
    2
    3
    1. Wired Speed Sensor with Mounting Bracket
    2. Extra Clear Front Cover
    3. Bracket Rubber Pad
    4. Bracket Rubber Pad (Riser Handlebar)
    5. Bladed Spoke Magnet
    6. Spacer
    7. Head Unit Battery (CR2032, 3-Volt)
    8. Wire Securing Tape
    9. Zip-Ties
    BUTTON FUNCTIONS
    HEAD UNIT
    Press momentarily
    Button : Lower Screen Modes
    Press & hold for 2 seconds
    Button & when the lowest screen is in the CLK Mode: NOM Setup
    Button & when the lowest screen is in the DST Mode: Reset Ride Data
    1
    2
    2
    1
    2
    1
    2
    1.0
    1
    2
    Attach the Wired Speed Sensor with the Zip-Ties supplied and tighten the Bladed Spoke Magnet to the bicycle. Mounting
    the sensor as high up as on the fork leg (see Fig. A). Adjust the sensor and magnet spacing with the Spacer. Remove
    the Spacer after snugging the Zip-Tie down to hold the sensor in its final position.
    WIRED SPEED SENSOR & MAGNET
    Wired Speed Sensor
    Wired Speed Sensor
    Fork Leg
    Bladed
    Spoke Magnet
    Bladed
    Spoke Magnet
    Bladed
    Spoke Magnet
    Bladed Spoke Magnet
    Spoke
    Magnet
    Sweep Path
    Zip-Tie
    Spacer
    Spoke
    Spacer Tip
    Alignment Mark
    Fig. A
    MOUNTING BRACKET & HEAD UNIT
    Attach Mounting Bracket & Bracket Rubber Pad to
    the handlebar on the “Sensor side” using the
    Zip-Ties provide. Adjust its position to your liking
    and tighten the Zip-Ties. Note: Be sure to leave
    enough slack in the wire to accommodate the
    movement of fork and handlebars. (See Fig. A)
    Slide the Head Unit into the Wired Mounting
    Bracket as shown until it clicks into position.
    Remove by pressing in the two locking tabs as
    shown.
    Secure wire with tape supplied and by winding it
    around cables.
    Locking Tab Locking Tab
    UNLOCK UNLOCK
    Wired Mounting Bracket
    Head Unit
    INSTALLATION TESTS
    Once installation is complete, the computer should be tested to make sure it is working properly.
    Pick up the front of the bicycle and spin the front wheel. The LCD should display a speed- reading within 2-3 seconds.
    SERVICE TIMER
    SETUP & PROGRAMMING
    12/24 CLOCK
    TIME
    In Setup, Button is used to select or set a value and to advance to the next digit or Mode. Button is used to switch
    between settings and to increase values.
    Initial Setup
    RT233 is programmed to enter the Initial Setup Mode after new battery replacement.
    In the Initial Setup, riders can program the Basic Settings for the computer, the content of settings are same as NOM
    Setup for Basic Setting.
    NOM Setup
    After completed the Initial Setup, riders can change any values or correct any errors by re-entering the NOM Setup.
    To enter the NOM Setup Mode press & hold & simultaneously when the lowest screen is in the CLK Mode.
    Important: Computer CANNOT exit during the Setup Mode until all the Basic Settings are finished.
    1
    2
    1 2
    If there is no speed-reading, check the alignment and spacing between the magnet and sensor. Make sure that the Head
    Unit is completely locked into position. If these checks do not solve the problem, talk to an Authorized Vetta’s Retailer or
    connect to www.vetta.com.
    Important: Make sure the magnet locking screw and all Zip-Ties are properly tightened.
    Press to toggle between flashing 12 and 24 hour formats.
    Press
    1
    to select your desired format (without PM icon implies
    AM in 12 hour format) and advance to Time setting.
    2
    Press to advance hour digits to correct hour (hold button for rapid advance). Press to select and advance to minute
    setting. Press to advance minute digits to correct minute. Press to select and advance to the next Setup Mode.
    2
    1
    2
    1
    Service Timer could be programmed with a selected number of ride time (hours or days) or distance as the interval for
    servicing the bicycle or any component on it, such as a front or rear shock.
    The default settings “0000” means the Service Timer is turned off.
    Press to scroll flashing hr (hour), day or dst (distance) as the Service Timer unit. Press to select the desired Service
    Timer unit.
    When the desired Service Timer unit has been chosen, press to scroll the flashing digit to the desired number. Press
    1
    to select this number and advance to next digit. Repeat this procedure until all digits are selected. Press to advance
    the next Setup Mode. ( Maximum settings: hour / day / distance = 1999 / 999 / 9999 )
    2
    1
    2
    1
    SPEED/ DISTANCE UNIT
    2
    1
    Press to toggle between flashing M/hr and KM/hr. Press to select
    and advance to the next Setup Mode.
    Note: Speed/Distance Unit cannot be changed if there have been ride
    data on screens. If you want to change the Unit, please make sure you
    had cleared all ride data before entering the NOM Setup Mode. This
    restriction does not apply to the Initial Setup after the 1
    st
    time battery
    installation, new battery replacement or All Clear Total Reset.
    2
    2 1 2
    2
    1
Vetta RT233

Нужна помощь?

Количество вопросов: 0

У вас есть вопрос о Vetta RT233 или вам нужна помощь? Задайте его здесь. Полно и четко опишите проблему и сформулируйте свой вопрос. Чем больше вы сообщите о проблеме или вопросе, тем легче будет производителю Vetta RT233 вам ответить.

Посмотреть руководство для Vetta RT233 бесплатно. Руководство относится к категории Велокомпьютеры, 1 человек(а) дали ему среднюю оценку 8.7. Руководство доступно на следующих языках: Engels. У вас есть вопрос о Vetta RT233 или вам нужна помощь? Задайте свой вопрос здесь

Технические характеристики Vetta RT233

Главная
Бренд Vetta
Модель RT233
Изделие Велокомпьютер
Язык Engels
Тип файла PDF

Часто задаваемые вопросы

Ниже приведены самые часто задаваемые вопросы о Vetta RT233.

Не нашли свой вопрос? Задайте свой вопрос здесь