Vetta RT255L

Vetta RT255L инструкция

(2)
  • Vetta’s RT200 series are the upgraded version of all RT series cycle computers. It is recommended that these
    products are to be installed by a qualified bicycle retailer. Failure to read the instructions and/ or improper installation
    of the device may void the warranty. If you have any doubts about the installation or the operations, contact your local
    bicycle retailer for clarification.
    WARNINGS & CAUTIONS
    HEAD UNIT
    COMPONENTS
    RT255 RT255L
    RT277 RT288 RT288L
    1. Button
    2. Button
    3. Button
    4. Button (RT255L/288L)
    5. Main Display
    6. Contact Pins (RT255/255L/277)
    7. Battery Compartment
    8. Battery Cap
    Heavy Duty Metal Braided Cable
    Wireless Transmission
    Replaceable Front Cover
    Screen Display Window
    NiteLite w/ SmartLite
    EZ Tire Set
    Service Timer
    Speed Comparator
    Auto Awake & Start-up
    Energy Efficient programmable Auto Start
    Current Speed
    Average/Maximum Speed
    Ride Time
    Cumulative Odometer
    Trip Distance
    Multi Freeze Frame Memory
    Lap
    Current/Average/Maximum Cadence
    12/24 Hour Clock
    FUNCTIONS / FEATURES
    RT255/255L includes: 1 3 4 5 9 11 12 14 15
    RT277 includes: 2 3 4 5 9 10 11 12 14 15
    RT288/288L includes: 3 4 5 6 7 8 9 11 12 13
    1. Wired Spd Sensor with Mounting Bracket
    (with Heavy Duty Harness)
    2. Wired Spd & Cad Sensor with Mounting Bracket
    (with Heavy Duty Harness, for Rear Wheel Pick-up)
    3. Extra Clear Front Cover
    4. Bracket Rubber Pad
    5. Bracket Rubber Pad (Riser Handlebar)
    6. WL Wireless Speed Transmitter
    7. Wireless Mounting Bracket
    8. Wireless Transmitter Shim
    9. Bladed Spoke Magnet
    10. Composite Cadence Magnet
    11. Spacer
    12. Head Unit Battery (CR2032, 3-Volt)
    13. Wireless Transmitter Battery (A23, 12-Volt)
    14. Wire Securing Tape
    15. Zip-Ties
    1
    2
    3
    4
    RT255 RT255L RT277 RT288 RT288L
    11 16 11 11 16
    10 15 10 10 15
    3 3 3 3 3
    1.0
    4
    5
    1
    3
    2
    6
    7
    8
    1
    7 8 9
    10
    11 12 13 1514
    2
    4
    3
    5 6
    LCD DISPLAY
    1. Upper Display
    2. Middle Display (Speed)
    3. Lower Display
    4. Service Timer/ Low Battery Icon
    5. Speed Comparator Icon
    6. Speed / Distance Units
    7. Setup Mode Icon
    8. Function Icons
    9. RPM / RT/ PM/ TM Icon
    10. Speed & Split Time Icon
    11. Freeze Frame Memory Icon
    12. Lap Icon
    13. Auto Start Icon
    1
    2
    5
    6
    7
    8
    9
    10
    11
    13
    12
    4
    3
    Important: Do not use Zip-Ties, use the tapes provided with the package to hold wires to the frame, fork, bars or stem
    to avoid damaging or cutting the wires accidentally. Make sure excess wire is taped down or wrapped around brake cable
    housing to secure it.
    BATTERY INSTALLATION
    INSTALLATION
    WIRED CADENCE SENSOR & MAGNET (
    RT277)
    Attach the Wired Cadence Sensor & Composite Cadence Magnet with the Zip-Ties supplied to the bicycle. Adjust the
    sensor & magnet spacing with the spacer. Remove the Spacer after snugging the Zip-Ties down to hold the sensor in its
    final position.
    4
    1
    3
    2
    BUTTON FUNCTIONS
    WIRED SPEED SENSOR & MAGNET (
    RT255/255L)
    Press momentarily
    Button : Upper Screen Modes
    Button : Lower Screen Modes
    Button : F-Button or Lap Button
    Button : NiteLite (RT255L/288L)
    Press & hold for 2 seconds
    Button : Recall Freeze Frame Memories or Lap Data
    Button & when the lowest screen is in the CLK Mode: NOM Setup
    Button & when the lowest screen is in the DST Mode: Reset ride data
    to zero including the Frozen screens or Lap data
    Button , & : All Clear Total Reset
    Wired Cadence Sensor
    Crank
    Arm
    Chain Stay
    Spacer
    Spacer
    Tip
    Alignment Mark
    Crank Arm
    Composite Cadence
    Magnet
    Wired Cadence Sensor
    Zip-Tie
    Composite
    Cadence Magnet
    Composite
    Cadence Magnet
    Composite
    Cadence Magnet
    Wired Speed Sensor
    Wired Speed Sensor
    Fork Leg
    Bladed
    Spoke Magnet
    Bladed
    Spoke Magnet
    Bladed
    Spoke Magnet
    Bladed Spoke Magnet
    Spoke
    Magnet
    Sweep Path
    Zip-Tie
    Spacer
    Spoke
    Spacer
    Tip
    Alignment Mark
    Fig. A
    1
    2
    3
    4
    3
    1
    1
    1 2
    2
    3
    2
    Magnet Sweep Path
    The RT200 series Head Unit use CR2032, 3-Volt Lithium button Cell batteries.
    Battery Run Time (1 hour training / day): Approx.12 months (RT255/255L/277); Approx. 8 months (RT288/288L)
    Important: Most cycle computer problems are caused by weak or
    dead batteries. See the Trouble Shooting section near the end of
    the manual for details.
    1. Remove the battery cap from the bottom of the Head Unit using
    a coin.
    2. Install a new battery as shown with the positive (+) side facing out. Do not touch or bend
    any of the battery contacts during installation.
    3. Screw the battery cap firmly into place and make sure that the O-ring seal does not get pinched or distorted.
    Caution: To avoid damage to the battery cap, do not over tighten.
    HEAD UNIT
    The WL Wireless Speed Transmitter uses an A23, 12-Volt battery. Remove the battery compartment using a coin and
    install the battery in it with positive (+) side in, then replace the battery compartment.
    Battery Run Time (1 hour training / day): Approx.10 months
    WL WIRELESS SPEED TRANSMITTER (
    RT288/288L)
    A23, 12V
    Attach the Wired Speed Sensor with the Zip-Tie supplied and tighten the Bladed Spoke Magnet to the bicycle. Mounting
    the sensor as high up as on the fork leg. (Fig. A) Adjust the sensor and magnet spacing with the Spacer. Remove the
    Spacer after snugging the Zip-Tie down to hold the sensor in its final position.
    WL WIRELESS SPEED TRANSMITTER & MAGNET (
    RT288/288L)
    Tie the WL Wireless Speed Transmitter with Bracket Rubber Pad loosely by the Zip-Ties supplied to either in the front of
    the left fork leg (see Fig.1 A) or at the back of the right fork leg (see Fig.1 B). For best signal reception, make sure the
    distance between the Transmitter and the Head Unit is within 70 cm. At the same time, the Transmitter should be
    2 ~ 4 cm (or more) away from the brake, to avoid blocking transmission signals by the brake. Adjust the transmitter
    and magnet spacing with the Spacer. Slide and rotate the transmitter until the alignment mark just touches the spacer tip
    on the magnet. Remove the Spacer after snugging the Zip-Tie down to hold the transmitter in its final position.
    Within 70 cmWithin 70 cmWithin 70 cm
    2~4 cm2~4 cm
    2~4 cm
    Fig.1 B
    Fig.1 A
    1
Vetta RT255L

Нужна помощь?

Количество вопросов: 0

У вас есть вопрос о Vetta RT255L или вам нужна помощь? Задайте его здесь. Полно и четко опишите проблему и сформулируйте свой вопрос. Чем больше вы сообщите о проблеме или вопросе, тем легче будет производителю Vetta RT255L вам ответить.

Посмотреть руководство для Vetta RT255L бесплатно. Руководство относится к категории Велокомпьютеры, 2 человек(а) дали ему среднюю оценку 8.7. Руководство доступно на следующих языках: Engels. У вас есть вопрос о Vetta RT255L или вам нужна помощь? Задайте свой вопрос здесь

Технические характеристики Vetta RT255L

Главная
Бренд Vetta
Модель RT255L
Изделие Велокомпьютер
Язык Engels
Тип файла PDF

Часто задаваемые вопросы

Ниже приведены самые часто задаваемые вопросы о Vetta RT255L.

Не нашли свой вопрос? Задайте свой вопрос здесь